Network troubleshooting technician providing live chat help

Joe B.

Reviewed for technical accuracy

Specialities: Home networking, Wi-Fi routers, modems, Windows/macOS internet issues, DNS & IP configuration, ISP setup

Fix router showing No WAN connection — WAN IP 0.0.0.0, WAN disconnected, Wi-Fi no internet

Technician avatar Technician
Hi! We’ll sort out that router showing No WAN connection and get everything back online. I just need a quick picture of your setup so we can target the right WAN fix.

When you log into the router’s web page, does the Internet/WAN status actually say “No WAN connection” or show a WAN IP of 0.0.0.0? Is the Internet/WAN light on the router solid, blinking, red, or completely off?

Also, do you have a separate modem + Wi-Fi router, or a single combo box from your ISP? And if you plug one computer directly into the modem, do you get internet there, or does no internet connection happen even without the router?
Customer
We have a cable modem from our ISP and a separate ASUS router. If I log into the router, at the top it says “No WAN connection” and the WAN IP address shows as 0.0.0.0. The Wi-Fi network still broadcasts and all devices can connect to it, but there’s no internet on anything. The modem’s Online light is solid, but the router’s Internet/WAN light is amber. I’ve rebooted the router a few times and power cycled it, but the WAN status never changes from Disconnected.
Technician avatar Technician
Thanks, that’s exactly the detail we need. A router showing No WAN connection with 0.0.0.0 usually means the router is not receiving an IP from the modem/ISP at all. Common reasons:

• The Ethernet cable from the modem is in a LAN port instead of the WAN/Internet port on the router.
• The router’s Internet connection type is wrong (for example set to PPPoE or Static IP when your ISP uses Automatic/DHCP, or the opposite).
• The modem is still “locked” to a previous device’s MAC address and refuses to give the new router a WAN lease.
• The modem is still doing routing/NAT and the router is also doing routing, which can cause a messy double NAT / WAN disconnected situation on some models.

We’ll first prove the modem and ISP really do have internet, then walk through physical ports, power cycling, and WAN IP settings to clear the “No WAN connection” error and replace that 0.0.0.0 with a real public IP.
Customer
If I bypass the router and plug my Windows PC directly into the cable modem with Ethernet, the internet works fine — normal speeds, everything loads. So the ISP side seems okay. As soon as I put the router back between the modem and the PC, the ASUS interface goes back to “WAN: Disconnected” and shows the WAN IP as 0.0.0.0 again, and all Wi-Fi devices lose internet.
Technician avatar Technician
Perfect test — that confirms the modem and ISP are fine and that the problem is specifically the router’s WAN connection to the modem.

Step A — Clean power cycle and cabling check for No WAN connection
1) Power off the router and modem (unplug power from both).
2) Make sure the Ethernet cable from the modem is going into the router’s WAN/Internet port (often a different color), not one of the four LAN ports.
3) Disconnect any extra cables from the modem so it’s only connected to power, coax/fiber, and the router’s WAN.
4) Plug in and power on the modem first. Wait until the Online/Internet lights are fully solid — give it 2–3 minutes.
5) Then power on the router and wait until the Power and Wi-Fi LEDs are stable.
6) On a computer connected to the router, log into the router’s admin page (192.168.0.1, 192.168.1.1, or whatever it uses) and check the WAN/Internet status section again: does it still show No WAN connection / 0.0.0.0, or do you see a real IP address?

If the WAN IP is still 0.0.0.0 after this clean start, the router is not successfully talking to the ISP through the modem, and we’ll adjust its WAN type and MAC address next.
Customer
I followed those steps exactly and confirmed the cable is in the blue WAN port. After the modem came up and I powered the router back on, the WAN page still says “Disconnected” and the IP is 0.0.0.0. Connection type is set to “Automatic IP (DHCP)”. Our ISP did have us use PPPoE on a really old router years ago, but I’m not sure what it is now. The modem itself is in router mode, I think, because its own web page hands out 192.168.100.x addresses.
Technician avatar Technician
Good info. There are two common patterns that make a router show No WAN connection even though the modem is online:

• The ISP expects the PPPoE username/password on the router, but the router is set to DHCP.
• The modem is already doing routing/DHCP, and the ISP has “locked” the connection to the MAC address of a different device that was previously connected.

Step B — Match ISP WAN type and clear MAC lock
• If your ISP says they use PPPoE, go to the router’s Internet/WAN settings and change the connection type from Automatic IP (DHCP) to PPPoE, then enter the exact PPPoE login they provided (this is separate from your Wi-Fi password).
• If they confirm it’s Dynamic IP / DHCP, leave it on DHCP but use the router’s “MAC address clone” or “Use this computer’s MAC” option to copy the MAC address of the PC that works when plugged directly into the modem.
• After saving, reboot the modem again, then the router, so the ISP sees the “new” device and issues a WAN lease.

Once this is done, refresh the Status page and check if that WAN IP 0.0.0.0 is replaced by a real address (often starting with 10.x, 100.x, or something like 73.x.x.x). If the status changes from No WAN connection to Connected, Wi-Fi devices should stop getting “no internet” errors. If it still says WAN disconnected, we’ll also check whether the modem should be in bridge mode instead of router mode.
Customer
I called the ISP and they confirmed it’s DHCP now, not PPPoE. I used the “Clone MAC address” option on the router with my PC’s MAC and then rebooted the modem and router again. Now the router status shows “WAN: Connected” and it has a 192.168.0.10 address from the modem instead of 0.0.0.0. But some devices still say “Connected, no internet” and certain websites time out, even though the No WAN connection warning is gone.
Technician avatar Technician
Great — we’ve fixed the main No WAN connection / 0.0.0.0 problem. The router now has a WAN IP, so the remaining “no internet” symptoms are usually DNS or double-NAT related.

Because your modem is also handing out 192.168.x.x addresses, you essentially have a router behind a router. That’s not always fatal, but combined with odd DNS settings it can cause pages to time out.

Step C — Clean up DNS and LAN IP on your router
1) In the router’s LAN settings, make sure its internal network is something like 192.168.1.x if the modem is using 192.168.0.x — you want different subnets so WAN and LAN don’t overlap.
2) In the WAN settings, set DNS to “Obtain DNS automatically from ISP” for now, unless your ISP told you to use specific DNS servers.
3) Apply/save, then reboot the router.
4) On one Windows laptop, set its Wi-Fi adapter to obtain IP and DNS automatically, then in Command Prompt run:
  • ipconfig /release
  • ipconfig /renew
  • ipconfig /flushdns

After that, reconnect to Wi-Fi and test a couple of websites. If that laptop starts working reliably while others still show “Wi-Fi connected but no internet”, we’ll repeat the IP/DNS reset on the remaining devices. If none work, we may want to put the modem into bridge mode so your router becomes the only device managing WAN and DHCP.
Customer
I changed the router LAN to 192.168.1.x, left DNS on automatic, and ran the IP/DNS reset on my laptop. That laptop is now browsing fine with no errors. Phones started working again after I toggled Wi-Fi off and back on. However, my work PC that’s wired to the router keeps dropping — it goes online for a bit and then the router interface briefly flashes “WAN: Disconnected” before reconnecting.
Technician avatar Technician
That’s a classic case of intermittent WAN drops — the router briefly loses its WAN lease, flips back to No WAN connection, then recovers. Let’s make sure it’s not a physical or firmware problem.

• First, swap the Ethernet cable between the modem and the router’s WAN port and, if possible, try a different WAN/Internet port if your router has more than one labeled for WAN.
• Ensure the modem and router are in a cool, ventilated spot — overheating can cause the WAN link to drop and reconnect repeatedly.
• In the router admin page, check for a firmware update. Install the latest stable firmware; many vendors explicitly mention fixes for “WAN disconnected” or “WAN 0.0.0.0” issues in release notes.
• On the work PC, temporarily disable any VPN client or advanced security software that could be hammering the connection with too many concurrent sessions, which can stress older routers.

After updating firmware and swapping the cable, monitor the Status page for a few minutes while browsing or running a speed test. The goal is for the WAN connection line to stay solidly on “Connected” without flipping back to 0.0.0.0.
Customer
I replaced the cable between the modem and router and updated the router firmware. Since then the status hasn’t gone back to “No WAN connection” and the WAN IP stays stable. The wired work PC is no longer dropping off. Everything — Wi-Fi and Ethernet — seems solid now. Is there anything else I should do to prevent the WAN connection from disappearing again?
Technician avatar Technician
Nice work — we’ve gone from router showing No WAN connection with 0.0.0.0 to a stable WAN IP and working devices. Let’s harden things so this doesn’t become a recurring headache.

Step D — Prevent future No WAN connection errors
• Leave the modem in bridge mode (or ask your ISP to enable it) if they support that, so your router is the only device doing routing, DHCP, and NAT. This removes most double-NAT/WAN confusion.
• Turn on automatic firmware updates in the router if available, or check manually every month or two for any WAN stability fixes.
• Take a screenshot of the working WAN configuration (connection type, MAC clone status, LAN IP) and save it somewhere safe so you can quickly rebuild it after a factory reset or replacement router.
• Change the router’s default admin password and disable remote administration from the internet unless you specifically need it — malware-infected routers often show random WAN disconnected behavior.
• Consider plugging the modem and router into a small UPS/battery backup to avoid brief power drops that can leave the modem locked and the router stuck on “No WAN connection” until they’re rebooted in the right order.

With those steps, your WAN link should stay stable for the long term. And if “router showing No WAN connection” ever pops up again, you’ll know exactly where to look and what to change.
Customer
Got it. I put the modem into bridge mode, enabled auto-updates on the router, and saved screenshots of the WAN settings. Everything has been steady for the last hour — no 0.0.0.0, no WAN disconnected messages. Really appreciate how you walked through each step.
Technician avatar Technician
You’re very welcome — glad we could get your WAN connection and Wi-Fi fully back online.

Summary: To fix a router showing No WAN connection, verify the modem has internet on a wired test PC, connect modem → router using the WAN port, power cycle in the correct order, match the ISP’s WAN type (DHCP or PPPoE), clone MAC if needed, and make sure the router gets a real WAN IP instead of 0.0.0.0. Then clean up LAN subnet, DNS, and device IP settings and keep firmware updated. If the WAN status ever flips back to “Disconnected”, you can open a chat with an expert and we’ll trace it live with you.
Customer
Everything’s working now and actually feels faster. Thanks again for helping me get rid of the “No WAN connection” message and explaining what all the WAN settings mean.
Technician avatar Technician
Any time! If a friend or coworker says their router is showing No WAN connection, the WAN IP is 0.0.0.0, or their Internet/WAN light is red, you can share this checklist with them — and if you’d like someone to click through the router status and WAN settings with you in real time, just start a chat with an expert and we’ll take it from there.

Quick answer: the accepted fix

Accepted fix when a router is showing No WAN connection: confirm the modem has internet by testing a PC directly, then power cycle modem and router in order, connect modem to the router’s WAN/Internet port, set the correct WAN type (DHCP or PPPoE) and clone MAC if needed so the router gets a real WAN IP instead of 0.0.0.0, and reset device DNS/IP settings so “Wi-Fi connected, no internet” clears on all devices.


Why routers show No WAN connection (modem, WAN IP, MAC, DNS)

Most home router showing No WAN connection problems come down to how the router and modem talk to each other, not to your phone or laptop. A missing or wrong WAN IP address (often 0.0.0.0), incorrect PPPoE vs DHCP selection, a modem that’s still bound to an older device’s MAC address, or overlapping LAN/WAN networks can all cause your WAN status to stay Disconnected even while Wi-Fi appears to be working locally.

Separating the path into segments — device → router (LAN) → router WAN → modem → ISP — makes it easier to see where the “No WAN connection” actually happens. If a laptop gets online when plugged straight into the modem but sees no internet when connected through Wi-Fi, the job of the router is where you focus: its WAN port wiring, WAN type, DHCP, DNS, and MAC address settings.

How to check whether the problem is WAN, modem, or device

To quickly narrow down a router showing No WAN connection issue, start with simple checks in the right order:

First, connect a computer directly to the modem. If that wired test has a working internet connection, your ISP and modem are fine. Next, reconnect the router and log into its admin page to see whether the Internet/WAN status says Connected and shows a live WAN IP, or still shows 0.0.0.0. If the router has a proper WAN IP but one device does not work, the problem is that device’s network adapter, DNS, or Wi-Fi profile. If all devices are affected and the router dashboard keeps showing “No WAN connection” or “Disconnected”, focus on the WAN port cable, ISP WAN type (DHCP vs PPPoE), MAC cloning, and whether the modem should be in bridge mode.

Router showing No WAN connection — quick troubleshooting tips

Confirm the modem and ISP first, then fix WAN IP, MAC clone, and DNS settings on the router.

Fast path: test internet directly from the modem → connect the modem to the router’s Internet/WAN port only → reboot modem, then router → set the correct WAN type (DHCP, PPPoE, or static IP) and use MAC address clone if your ISP has locked the line to a previous device → verify the router gets a real WAN IP instead of 0.0.0.0 → set IP/DNS to automatic on devices and briefly reconnect them to Wi-Fi. Updating firmware and disabling unneeded remote admin features helps avoid random “WAN disconnected” issues in the future.

Disclaimer: This information is AI-generated and intended for general guidance only. For advice specific to your router model and ISP, please consult a verified expert on Whizz-Tech before making decisions.


Getting Started Is Easy

Ask for help, 24/7

Members enjoy round-the-clock access to 12,000+ verified Experts for router showing No WAN connection, WAN IP 0.0.0.0, Wi-Fi connected but no internet, slow speeds, and more.

Expert will respond in minutes

We match you with a networking specialist who knows modems, WAN ports, DHCP, PPPoE, DNS, and router setup for all major brands (Netgear, TP-Link, ASUS, Linksys and more) so you can quickly clear that “No WAN connection” warning.

Save time & money

Stop endlessly rebooting your router and guessing at WAN settings. Get a clear step-by-step No WAN connection fix in chat and get back online quickly without waiting on hold for your ISP.

FAQ

Why is my router showing No WAN connection?

Often, the modem and ISP are working but the router’s WAN configuration is wrong. Common causes include the router not getting a WAN IP address (it stays at 0.0.0.0), using the wrong connection type (DHCP vs PPPoE), a bad Ethernet cable between modem and the router’s WAN port, the modem not being in bridge mode, or firmware glitches. Checking the Internet/WAN status page will usually reveal which of these is causing the “No WAN connection” error.

How do I fix WAN IP 0.0.0.0 on my router?

If your router’s WAN IP shows 0.0.0.0, start by power cycling the modem and router in order and making sure the modem is cabled into the WAN/Internet port. Then confirm the ISP’s WAN type (Dynamic IP vs PPPoE), set that correctly on the router, and use MAC address clone if your ISP has locked the connection to a different device. Once set correctly, the WAN IP should update from 0.0.0.0 to a valid address and the No WAN connection status should disappear.

What lights should be on when the WAN connection is working?

On most home routers, you want a solid Power light, a solid or blinking Internet/WAN light, and activity lights for Wi-Fi (2.4 GHz / 5 GHz) and any active LAN ports. A red, amber, or off Internet/WAN light usually means the router is not successfully talking to the modem or ISP, even if Wi-Fi still appears to work.

When should I reset my router to factory settings for WAN issues?

If you’ve verified the modem works directly, replaced cables, set the correct WAN type, cloned MAC if needed, changed the LAN subnet, and updated firmware but the router still shows No WAN connection or 0.0.0.0, a factory reset is reasonable. Press and hold the reset button as instructed by the manufacturer, then rerun the setup wizard with your ISP details and recreate your Wi-Fi network and WAN settings from your saved notes or screenshots.

Sources

Matt Verified Icon
Matt ● replies in < 1 min
Technician Expert
⭐⭐⭐⭐⭐ Trusted by 27,000+ customers
Avatar
Alex · Expert's Assistant