Printer troubleshooting technician providing live chat help

Joe B.

Reviewed for technical accuracy

Specialities: Windows/macOS, Brother HL/MFC/DCP, Firmware, Networking, Office Equipment

How to fix “Brother prints blank pages” after firmware/driver update — HL, MFC, DCP

Technician avatar Technician
Hey! We’ll stop those blank pages. Tell me your exact model (HL-L2350DW, MFC-L2710DW, DCP-L2550DW, etc.), OS (Windows 11/10 or macOS), connection (USB/Wi-Fi/Ethernet), and what changed — a firmware update, Windows driver update, or a new toner/drum?
Customer
Windows 11, MFC-L2710DW over Wi-Fi. I installed a firmware update yesterday. Today everything prints blank — PDFs, test page, copies. Toner is new.
Technician avatar Technician
Thanks. After some Brother firmware updates the print engine can lose its bias settings or the NVRAM glitches. Windows can also swap the driver to Microsoft Class. Any of these cause blank pages. The cure is usually: factory reset → USB firmware reinstall or rollback → install the Full Driver & Software Package and test PCL vs BR-Script.
Customer
What should I try first? I need invoices to print right now.
Technician avatar Technician
5-minute clean fix for “Brother prints blank after update”:
1) Engine self-test: print Settings List / Network Report from the panel. If those are also blank, it’s a printer/firmware issue, not the PC.
2) Reseat TN/DR: remove the toner TN and drum DR unit, gently shake toner, reinstall until it clicks. Slide the corona wire back and forth and park on “▲”.
3) Make sure Toner Save = Off and Print Density ≥ 3.
4) Factory Reset (NVRAM): Initial Setup → Reset → Factory Reset (re-join Wi-Fi afterward).
5) Test again. If still blank — we’ll do a USB firmware reinstall.
Customer
Printer reports are blank too. Factory Reset didn’t help.
Technician avatar Technician
Engine recovery via USB:
• Connect the printer by USB (temporarily).
• Run the Brother Firmware Update Tool and choose Reinstall. If your model allows, perform a firmware rollback to the previous stable version.
• Install the latest Full Driver & Software Package. In Windows, test both PCL and BR-Script (PostScript) queues — sometimes one path goes blank after an update while the other prints fine.
Customer
I’m using a compatible toner. Could the firmware block it and cause blank pages?
Technician avatar Technician
Toner authentication: newer firmware sometimes tightens chip checks. That typically shows Replace Toner, not blank pages. To rule it out, test with an OEM TN cartridge. Also confirm the shutter opens and the primary charge roller isn’t contaminated.
Customer
Windows recently installed a driver. Could that be the reason?
Technician avatar Technician
Driver rollback (Windows): remove all Brother queues → install the Full Driver & Software Package → in Printer Properties → Advanced try Brother PCL and BR-Script. Turn off “Let Windows manage my default printer” so Windows doesn’t swap to a Microsoft Class Driver again.
Customer
Copying from the ADF also gives a blank sheet. So it’s not the PC?
Technician avatar Technician
Correct — if copies are blank, the issue is in the print engine. Try a quick cover-open test: start a print, open the cover to stop it, remove the TN/DR and inspect the page. If it’s pure white, it’s firmware/NVRAM. If you see a very faint image, clean the corona wire and check the transfer roller. Then redo the USB firmware reinstall.
Customer
Reinstalled firmware over USB and switched to BR-Script — printing is back. How do I keep it stable?
Technician avatar Technician
Great! For reliability:
• Disable Auto Firmware Update in the printer’s web UI (http://<printer-IP> → Administrator).
• Keep only one active queue (either PCL or BR-Script).
• If you use compatibles, keep one OEM TN handy for diagnostics.
• Save the working driver package and the firmware version so you can rollback quickly next time.
Customer
What about macOS if blank pages start after a Brother firmware update?
Technician avatar Technician
macOS path: remove the queue → Reset printing system → add via AirPrint/IPP. If the Brother CUPS driver prints blank but AirPrint works, stay on AirPrint for stability. If even the Settings List is blank, perform a Factory Reset and reinstall firmware over USB.
Customer
All good now. Thanks!
Technician avatar Technician
Summary: For Brother printer prints blank after firmware update — reseat TN/DR, turn off Toner Save, run a Factory Reset, then do a USB firmware reinstall/rollback. On Windows install the Full Driver & Software Package and test PCL vs BR-Script; on macOS prefer AirPrint/IPP. Need help choosing the right rollback file? Open the chat and I’ll walk you through it live.

Quick answer: the accepted fix

Accepted fix for Brother blank pages after firmware update: perform a Factory Reset, connect by USB, run the Brother Firmware Update Tool to reinstall or rollback firmware, then install the Full Driver & Software Package and test PCL vs BR-Script. Ensure Toner Save = Off, corona wire is clean, and TN/DR are seated correctly. If the Brother driver on macOS still fails, keep using AirPrint/IPP.


Blank pages after update — HL/MFC/DCP models

Common root causes after a firmware/driver update: engine bias reset, NVRAM corruption, or a driver mismatch. Typical searches include: Brother HL prints blank, MFC blank pages after update, copies blank. Solutions: USB firmware reinstall, firmware rollback, driver rollback, switch between PCL and BR-Script, and test with an OEM TN cartridge.

How to verify the fix

Print a Settings List and Network Report from the panel, then a 1-page PDF from your computer. Both should print solid black text. If they’re blank again, repeat the Factory Reset, reinstall firmware over USB, and try the alternate driver path.

Brother prints blank — troubleshooting tips

Usually caused by a firmware/driver mismatch or engine settings reset after an update.

Fast path: reseat TN/DR → Factory Reset → USB firmware reinstall/rollback → install Brother Full Driver and test PCL/BR-Script. Keep one queue only, disable auto firmware updates, and save the working driver package for future recovery.

Disclaimer: This information is AI-generated and intended for general guidance only. For advice specific to your environment, please consult a verified expert on Whizz-Tech before making decisions.


Getting Started Is Easy

Ask for help, 24/7

Members enjoy round-the-clock access to 12,000+ verified Experts, including tech support, mechanics, vets, and more.

Expert will respond in minutes

We match you with an Expert who specializes in your situation. Talk, text, or chat — whichever you prefer.

Save time & money

No scheduling hassles or expensive consults. Membership can save you significant time and money each month.

FAQ

Why does my Brother print blank pages after a firmware update?

Updates can reset engine bias or corrupt NVRAM, and Windows can swap to a Microsoft Class Driver. The fix is a Factory Reset, USB firmware reinstall/rollback, and installing the Full Driver & Software Package (test PCL vs BR-Script).

Windows: which driver should I use — PCL or BR-Script?

Start with Brother PCL. If pages are blank or washed out, switch to BR-Script (PostScript). Remove duplicate queues and disable Windows auto-management of the default printer.

macOS prints blank with the Brother driver but AirPrint works — what now?

Use AirPrint/IPP for reliability. Reinstall the Brother CUPS driver only if you truly need vendor-specific finishing options.

Could a compatible toner cause blank pages?

Firmware usually flags non-OEM toner as a supply error, not blank sheets. For diagnosis, try an OEM TN and check the corona wire, transfer roller, and cartridge shutter.

Common Brother blank-page problems and quick fixes
SymptomLikely causeQuick fix
Blank pages after firmware update NVRAM/engine bias reset Factory Reset; USB firmware reinstall/rollback
Blank pages only from PC Driver mismatch (PCL vs BR-Script) Install Full Driver Package; test PCL/BR-Script
Copies also blank Print engine issue Clean corona wire; reseat TN/DR; firmware reinstall
Random driver swaps Windows auto management Disable auto-manage; lock to Brother driver

Step-by-step (Windows 11/10)

  1. Remove existing Brother queues in Printers & Scanners.
  2. Factory Reset the printer (Initial Setup → Reset).
  3. Connect by USB and run the Brother Firmware Update Tool (reinstall/rollback).
  4. Install the latest Full Driver & Software Package and test PCL and BR-Script.

Optional: macOS path

  1. Remove the queue and Reset printing system.
  2. Add the printer via AirPrint/IPP; keep vendor CUPS driver only if needed.
  3. If device reports are blank, reinstall firmware over USB and test again.

Sources

Matt Verified Icon
Matt ● replies in < 1 min
Technician Expert
⭐⭐⭐⭐⭐ Trusted by 27,000+ customers
Avatar
Alex · Expert's Assistant